我們都知道消防設備是否合格，對人們的有著非常大的影響，如果發生火災等情況，而消防泵卻無法正常使用，那么危險性就會明顯增加，甚會危害到人們的生命財產了，因此近些年消防、等行業對該設備的故障問題重視，日常檢查的效率也明顯提高了，下面川消小編來說說消防泵主要故障問題有哪些。

We all know whether fire-fighting equipment is qualified or not, which has a great impact on people's safety. If there is a fire and the fire pump cannot be used normally, the danger will increase significantly, and even endanger people's life and property safety. Therefore, in recent years, the fire protection, environmental protection and other industries attach great importance to the failure of the equipment, and the efficiency of daily inspection has also improved significantly, Now let's talk about the main fault problems of fire pump.

1、液體提供要達標

1. Liquid supply must meet the standards

為什么會出現消防泵無法排出液體的情況呢?雖然該設備的結構比較簡單，但是出現故障的幾率還是比較高的，其中液壓不足的情況就很常見，這會導致設備無液體提供，如果不能及時發現故障問題，就會引發非常嚴重的問題了，檢查的時候務必要注意到這一點。

Why does the fire pump fail to discharge liquid? Although the structure of the equipment is relatively simple, the probability of failure is still relatively high. Insufficient hydraulic pressure is a common situation, which can lead to no liquid supply to the equipment. If the fault problem cannot be detected in a timely manner, it can cause very serious problems. It is necessary to pay attention to this when inspecting.

2、注意管線是否堵塞

2. Pay attention to whether the pipeline is blocked

除了之前提到的液體提供不足故障問題之外，管線堵塞的幾率也相當高，尤其是液體比較渾濁的情況下，會導致管線不斷堆積污垢，因此堵塞的情況就會頻繁的發生了，這也會影響消防泵的液體輸送效率，只要清理障礙物，就能讓設備恢復正常運行狀態。

In addition to the aforementioned problem of insufficient liquid supply, the probability of pipeline blockage is also quite high, especially when the liquid is relatively turbid, which will lead to continuous accumulation of dirt in the pipeline, so the blockage will occur frequently, which will also affect the liquid delivery efficiency of the fire pump. As long as the obstacles are cleared, the equipment can return to normal operation.

此外消防泵的流量不夠怎么了？

Besides, the flow of fire pump is not enough. Why?

1.密封環嚴重磨損或腐蝕?換新密封環。

1. Is the sealing ring severely worn or corroded? Replace the sealing ring with a new one.

2.半開式葉輪與消防泵蓋間隙太大?減小間隙。

2. Is the clearance between the semi open impeller and the fire pump cover too large? Reduce the gap.

3.吸入管路太細或雜物堵塞?換合適管路，雜物。

3. Is the suction pipeline too thin or blocked by debris? Replace the appropriate pipeline and remove debris.

4.葉輪嚴重磨損或嚴重腐蝕?換新葉輪。

4. Is the impeller severely worn or corroded? Replace the impeller with a new one.

5.吸入管浸泡的深度不夠，有空氣吸入消防泵內?增加吸入管的浸入深度。重裝消防泵用靜環。

5. The immersion depth of the suction pipe is not enough, and air is sucked into the fire pump? Increase the immersion depth of the suction pipe. Reassemble the stationary ring for fire pump.

以上就把消防泵的故障問題簡單的介紹給大家了，大致的看完介紹內容之后，我們可以知道更多的產品相關情況了，日常維護設備也會注意到更多的細節問題，其實維護頻率不用太高，只要定期維護就可以了。還有什么問題就來我們網站http://www.xintli.net關注留言！

Above is a brief introduction of the fire pump failure. After reading the introduction, we can know more about the product, and daily maintenance equipment will also pay attention to more details. In fact, the maintenance frequency should not be too high, as long as regular maintenance. If you have any further questions, please come to our website http://www.xintli.net Follow the message!